Selection Guide

ESD Bag Selection by Component and Route

Choose between antistatic, dissipative and shielding bags by component sensitivity and destination. A practical decision table for electronics buyers.

PSF Packaging Engineering · Published November 6, 2026 · Updated November 20, 2026 · 3 min read

Matte CPE bags holding a remote control, calculator and power strip
Matte CPE bags holding a remote control, calculator and power strip.
Short answer

ESD bag selection depends on component sensitivity and whether the package leaves an ESD-controlled area: bare PCBs and semiconductors require metallised shielding bags with surface resistance of 10⁶–10¹¹ Ω, while less sensitive assemblies can use dissipative bags. PSF Packaging supplies both structures with 7–15 working day lead times.

Key points

  • The first question is not price — it is whether the bag leaves the ESD-protected area.
  • Shielding, dissipation and moisture barrier are three separate functions.
  • Mixed assemblies with metal housings may need ESD and VCI protection together.
  • A failed seal removes shielding performance regardless of film specification.

Start with the shipping route

RouteESD area statusMinimum bag type
Workstation to workstation in the same ESD areaControlled throughoutDissipative
Factory to local assemblerLeaves controlled areaShielding
Factory to overseas customerLong transit, variable handlingShielding with moisture barrier
Factory to repair centreMultiple handoffsShielding, sealed, with label

Three bag types compared

TypeStructureProtects againstDoes not protect against
AntistaticInsulating film with antistatic additiveCharge generation on the bag itselfExternal discharge
DissipativeConductive-filled film, 10⁶–10¹¹ ΩControlled charge bleedDirect discharge from a charged source
ShieldingMetallised multi-layer, Faraday cageDischarge current through contentsMoisture unless barrier layer included

Component sensitivity

ComponentTypical sensitivityRecommended
Bare PCB with ICsHighShielding plus moisture barrier
Semiconductor devicesVery highShielding, sealed, desiccant where required
Connectors, passive partsModerateDissipative
Complete assembled unitLowerDissipative or shielding depending on market
Optical or sensor modulesHigh, plus physical sensitivityShielding with cushioning structure

When ESD and rust protection meet

Electronic assemblies with steel or aluminium parts have two failure modes at once: electrostatic discharge and corrosion. Using an ESD bag with loose VCI paper inside creates contamination risk around connectors. A combined structure — ESD shielding layer plus VCI additive in the seal layer — handles both in one package.

Specify all metals in the assembly when requesting VCI compatibility, because inhibitor chemistry is metal-specific.

Physical protection is a separate decision

Neither ESD nor VCI film protects against crushing or puncture. A bag rated 10⁶–10¹¹ Ω that is punctured in transit has no shielding performance. For fragile assemblies, add an EPE-laminated or bubble outer layer, and confirm that the cushioning material is ESD-safe when used inside an ESD package.

Boundary: what a bag cannot replace

An ESD bag does not replace grounding straps, grounded benches or ionised air in the assembly area. It protects the component during transport and handling outside that environment. If the failure occurs during assembly, the bag is not the corrective action.

For definitions, start with what is an ESD shielding bag. For corrosion, read the VCI rust preventive bag explanation.

This article describes general practice in flexible packaging. It is not a substitute for a specification review of your product — film structure, functional values and compliance depend on the contents, the packing line and the destination market.

Questions

Frequently asked

Do I need a shielding bag inside my own factory?

If the board stays inside a grounded ESD-protected area, a dissipative bag is often sufficient. Once it leaves that area — to a subcontractor, a warehouse or a customer — shielding is required.

What bag should I use for a PCB with a metal shield can?

The board still needs ESD shielding. If the metal parts are corrosion-sensitive, ask about a combined ESD and VCI structure rather than adding loose VCI paper that can contaminate connectors.

Are metallised bags see-through?

Metallised shielding bags are typically silver and opaque enough to obscure fine print. Where visual inspection of the contents matters, a transparent dissipative bag may be preferred — but it does not provide shielding.

What causes shielding bags to fail in transit?

The most common causes are seal failure, pinholes from sharp board edges and creasing that breaks the metallised layer. Use an inner cushion or a bag with adequate gauge for the contents.

Send your bag specification, get a quote

Give us the format, dimensions, film structure and artwork. You will receive an indicative price, a stated lead time and a clear answer on whether we can hold the specification — no obligation, and no sales call unless you ask for one.

Chat on WhatsApp