Inside the Plant: 3,000 m², 8+ Tonnes a Day

The production areas, the process chain and the inspection points — so you can check whether the film, print and converting steps your bag needs actually sit under one roof.

Short answer

PSF Packaging runs a 3,000 m² flexible packaging workshop in Shenzhen, China, with 45+ staff and 8+ tonnes of daily output. Film blowing, offset and gravure printing, lamination, slitting, bag converting and inspection are integrated in one plant. The quality system has been ISO 9001 certified since 2019, with EU REACH compliance completed in 2022 and FDA 21 CFR 177.1520 food-contact structures supplied. Factory visits are arranged by appointment.

3,000 m²Workshop floor
45+Staff
8+ t/dayDaily output
7–15 daysProduction lead time
Production areas

What sits in each part of the workshop

Film, print, bags and inspection share the same 3,000 m² site, so a material change can be traced through to the finished bag without an outside handoff.

Film blowing workshop with a multilayer coextrusion line and rolls of PE and PP film
3,000 m² workshop

Film Blowing Workshop

Automatic film blowing lines coextrude PE, PP, CPE and POF structures in one pass, feeding printing and bag converting directly.

Fully automatic film blowing machines, introduced in 2017, build multilayer film at the die instead of laminating separate webs, so gauge and layer composition stay under one control point. The line produces PE, PP, CPE and POF structures; POF shrink film was developed in 2019–2020 and CPE matte and anti-static structures followed the 2017 upgrade. Because film, print and conversion sit in the same 3,000 m² workshop, a material change can be traced through to the finished bag without a handoff to an outside supplier.

Printing and laminating production line inside the PSF Packaging workshop
3,000 m² workshop

Printing Workshop

Offset and gravure printing run side by side, with 150 LPI halftone capability on film substrates.

The printing floor runs two processes — offset (胶版) and gravure (铜版) — and selects between them by run length and substrate rather than by press availability. Offset suits shorter runs on OPP and CPE bags where an engraved cylinder would not pay back; gravure holds density and fine halftones at 150 LPI over long runs. Keeping both processes in one building means the print method follows the order. The 2017 equipment upgrade added the offset presses alongside the film blowing lines.

Bag converting workshop with operators running bag-making machines
3,000 m² workshop

Bag Converting Workshop

Bag-making lines form heat-sealed, zipper and shaped bags from OPP, CPE, POF and PE film at a combined 8+ tonnes per day.

Converting turns printed film into finished bags: heat sealing, zipper (骨袋) closure and shaped or special-format bags. The 2017 expansion added OPP self-adhesive bags, CPE matte bags and anti-static bags; PLA biodegradable bags followed in 2022–2023. Line settings are held per film structure because a seal tuned for CPE will burn through a thinner PE film. The workshop supports a daily output of 8+ tonnes across the 3,000 m² site, with 45+ staff covering film, print and conversion.

Workers inspecting finished bags beside the production line in the PSF Packaging workshop
3,000 m² workshop

Quality & Inspection

Inspection is placed at incoming film, print, seal and finished-bag stages, with a 99.9%+ pass rate target over 8+ tonnes of daily output.

Checks sit at each process stage rather than only at the end of the line: a seal fault found after printing wastes the print as well as the film. Records are kept against the order so the ISO 9001 system certified in 2019 and the EU REACH and FDA 21 CFR 177.1520 claims can be traced to the material and batch concerned. A 99.9%+ pass rate is the working target across 8+ tonnes of daily output. Inspection covers the same structures the workshop sells — ESD shielding, zipper, OPP, CPE, POF and PLA bags.

Process chain

From resin to finished bag

Each step is specified against the approved sample. A bag does not lose its record when it moves between operations, because the same specification follows it through the plant.

Stage What happens
Film blowing Fully automatic lines coextrude PE, PP, CPE and five-layer POF film in-house, introduced from 2017 onward.
Printing Offset (胶版) and gravure (铜版) printing up to 150 LPI, chosen by run length and substrate.
Lamination Barrier and metallised layers are combined for ESD shielding and VCI structures, fixed at sample approval.
Slitting Parent rolls are slit to the bag width required by the order, matched to downstream bag-making lines.
Bag converting Heat sealing, zipper closure, card-head holes and shaped bags across OPP, CPE, POF and PE film.
Inspection Checks at each stage against the approved sample, supporting a 99.9%+ delivery pass rate.

A manufacturing execution system (MES) was introduced in 2024 to hold process data across these stages. Per-machine models and counts were not supplied, so they are not listed here.

Photographs · Production floor

The workshop and its machines

Real photographs of the PSF Packaging plant in Shenzhen — the film blowing, printing and bag-converting lines, and the inspection area. These are our own production facilities, not stock imagery.

Photographs · Finished products

Bags made in this plant

A selection of real product photographs — ESD shielding bags, zipper and matte bags, aluminium-foil pouches, food bags and printed retail packaging. Each image shows actual PSF output; no unrelated product imagery is used.

Audits and visits

Come and look at it

A factory page is a claim; a visit is evidence. We arrange customer visits and audits by appointment, covering the route your bag will take — incoming film, printing, converting, inspection and packing. A remote video tour is available where travel is impractical.

  • On-site visits arranged by appointment, including customer-specific checklists
  • Remote video tour of the film blowing, printing and converting areas
  • Records available on site: sample approvals, inspection records and compliance statements
  • NDA signed before any customer artwork is shown during a tour

Arrange a visit

ISO 9001 Issuing body not disclosed Quality management system for the manufacture of packaging film and bags
EU REACH compliance EU REACH regulation Materials compliance for packaging supplied to the European Union market
FDA 21 CFR 177.1520 U.S. Food and Drug Administration Food-contact compliance for polyolefin film and bags made from olefin polymers

Send your bag specification, get a quote

Give us the format, dimensions, film structure and artwork. You will receive an indicative price, a stated lead time and a clear answer on whether we can hold the specification — no obligation, and no sales call unless you ask for one.

Chat on WhatsApp